Thermal Electronics Corp. | Home | INTRODUCTION | THERMOELECTRIC POWER GENERATOR SYSTEMS FOR SALE | Thermoelectric Peltier Effect Power supplies, TEG POWER Seebeck Effect Regulators | TEG THERMOELECTRIC POWER MODULE SELECTION | THERMOELECTRIC TEG POWER MODULES UNDER 200°C | MilkMate 2000 L | MilkMate 2005 | Solar Hot Water Heater & TEG Power Generators | How Thermoelectric Power Generation Works | What's News | MilkMate 2000 (1 Gallon) | TEG Power Generator & Thermoelectric Generator | Thermoelectric PARTS Heat sinks- Heat Pipes | MilkMate Merchandiser 4Q | MilkMate 2G ( 2 Gallon Fridge ) ONLY 8" WIDE | Custom Thermoelectric Peltier Effect Appliance Design & Manufacturing | Wine Cabinets & Accessories | Thermoelectric Peltier cooler Module Selection | Glossary of Thermoelectric Terms | GAS MONITORING SYSTEMS | Countertop Gelato Display Case | Contact Us
North America
1-800-769-2395
USA
1-815-349-7004
Outside North America
1-905-751-1362
We offer thermoelectric power
assemblies which in the place of a heat exchanger can not only power all your pumps in your water heater system but can also provide power to charge batteries for emergency power back-up!
call or e-mail us for details
1-800-769-2395 or info@espressomilkcooler.com
TEG POWER SYSTEMS
THERMOELECTRIC POWER MODULES
TEM POWER SYSTEMS
SEEBECK EFFECT POWER MODULES
Woodstove TEG generators
Boiler TEG Power
Generators
Thermoelectric woodstove Generators
Custom TEG Power Generator design
Solar Hot Water Heater & TEG Power Generators
 Evacuated tubes are the absorber of the solar rays. They absorb solar energy converting it into heat for use in water heating. Evacuated tubes have already been used for years in Germany, Canada, China and the UK. There are several types of evacuated tubes in use in the solar industry. Our collectors use the most common "twin-glass tube". This type of tube is chosen for its reliability, performance and low manufacturing cost.
 Each evacuated tube consists of two glass tubes made from extremely strong borosilicate glass. The outer tube is transparent allowing light rays to pass through with minimal reflection. The inner tube is coated with a special selective coating (Al-N/Al), which features excellent solar radiation absorption and minimal reflection properties. The top of the two tubes is fused together and the air contained in the space between the two layers of glass is pumped out while exposing the tube to high temperatures. This "evacuation" of the gasses forms a vacuum, which is an important factor in the performance of the evacuated tubes.
|
Adjacent is a heat pipe designed solar hot water heater. These solar heaters are ideal for cold weather climates. There is little water in the unit. The vertical pipes are vacuum tubes with heat pipes inside the vacuum glass tube. The pipe inside the glass tube vacuum is made of a copper tube containing purified water with additives. Coolant evaporates into a vapour when the suns heat penetrates the tube. The manifold at the top contains a food grade Glycol which circulates via a pump. The copper tube ends are exposed inside the manifold so the Glycol passing thru the manifold picking up the heat and transfers it to the hot water tank via a copper coil stored inside the water heater in the house.
   |
 The coils located inside the hot water heater transfer a large amount of heat as the heated Glycol is pumped through the coils. These solar hot water systems are ideal for pools and hot tubes. If the systems are designed properly they can store large amounts of heat to be used at a later time.
|
As you can see the explanation above is demonstrated in the adjacent image. A number of systems can be set up in series depending on your hot water needs to increase the amount of hot water required. We are also using a thermoelectric
TEG generator as the heat exchanger which,
will not only transfer heat, but also produce enough power to run the pumps independent of the grid and depending on the system supplement the power requirements of the household. The solar hot water heating systems can heat your water and charge batteries at the same time. Allowing for off grid power generation!
This a a small water to water TEG (Thermoelectric generator) This unit with a delta T of approximately 100-120C can produce 12-14 VDC nominal voltage and produce about 20-25 watts of power. This is enough power to run 12 VDC pumps on both the hot and cold side of a domestic solar hot water system. We are making larger units in the 50 to 100 watt range that will provide not only enough power to operate a commercial solar hot water system, but additional power to charge batteries for back up power. The off grid designs are ideal for areas which experience constant grid power disruptions.
Adjacent is a 50 watt thermo electric generator @ 13-14V output with a Delta T of 130C. It utilizes the seebeck effect. The outside pipes are used for cold service water and the inner central pipes are for the closed loop coolant attached to the solar heater. Using focused solar a temperature on the hot side of 150C (Vegetable Oil) with a cold side of 20C was achieved. This unit would be ideal for off-grid power generation.
|
Introduction |MilkMate 2000 (1 Gallon Cooler) | MilkMate 2000L |MilkMate 2005 | Merchandiser Fridge 4Q | Countertop Gelato Display Case | TEG Power Generator | THERMOELECTRIC POWER GENERATOR SYSTEM FOR SALE | How Thermoelectric Power Generation Works | What's News | TEG Design and prototypes |MilkMate 2G (2 Gallon) | Services & Custom TEC Manufacturing | Components | Components pg. 2| Wine Cabinets & Accessories | | Thermoelectric Module Selection | Glossary Of Thermoelectric Terms | Gas Monitoring System | Solar Hot water & TEG POWER GENERATORS | Contact US |
t
type=