Thermoelectric PARTS Heat sinks- Heat Pipes

Thermoelectric PARTS Heat sinks- Heat Pipes

Part # Ht-6-4-Assembly . Standard in stock

- consists of 1 size: 127mm (5")x 129.6mm (5.1")x 6.05cm (2.4") High 32 fin extruded heat sink

- 1 Extender block 40 mm x 40 mm face with 12 mm wings for fasteners with - 2 holes

22 mm apart and are tapped for 8-32 screws.( other size hole can be ordered)

- 1 closed cell neoprene gasket 3/8" thick.

- 1 TEC1-12706 Peltier module, 15 V max , 6 amps ,51.4 watts

- We also supply TEC1-12703, TEC1-12704 , TEC1-12706, TEC1-12708 and TEC1-127085

as substitute modules if required

CLICK TO VIEW PDF ON HEATSINK

Heat sink , thermo electric chip, cooling assembly, aluminum heat sink, 6 amp thermo electric, Peltier cooler, thermoelectrics , peltier chip , bonded heat sink , thermoeletric assemblies, extender blocks, solid state cooling , thermoelectric cooling

Heat sink assemblies complete with 6 amp, 15 Vmax thermo electric chips for cooling

Our heat sink is idle for cooling or Thermoelectric Power Generation applications!

Heat sink size:

W x L x H	5" x 5.125" x 2.5" extruded serrated fins	32 fins

Y o u C h o o s e	This is one of the most concentrated heat sink designs you can buy! Fin height is almost 2" alone (59mm) and is an extruded heat sink! All of our fins are serrated which adds additional surface area, with a thick base for heat spreading which, in turn, increases cooling efficiency for both cooling of peltier modules or cooling the cold side in thermoelectric power generation applications.

	Adjacent are 2 heat pipes we have designed to fit up to a 40mm module. The top heat pipe will accommodate a single module while the one below will hold two 40 mm modules. These heat pipes work as good or better than most extruded or bonded heatsinks.
	Other benefits include less cost and require less air flow , which in turn makes the system design more quite. They use evaporative cooling and use environmentally friendly water as the working fluid.

Call or e-mail for your specific requirement!

1-800-769-2395

Heat sink , thermo electric chip, TEG, Thermoelectric generators, solidstate generator, power generator, low temperature TEG generator, Waste heat power generator, remote power generator, BiTe couples, TEG components, thermoelectric generator parts, TEG Parts, TEG modules, Prototype TEG power Generator, Hot water power generator, Hot water TEG power Generator, cooling assembly, aluminum heat sink, 6 amp thermo electric, Peltier cooler, thermoelectrics , peltier chip , bonded heat sink , thermoeletric assemblies, extender blocks, solid state cooling , thermoelectric cooling, Toronto Ontario Canada, GTA, Newmarket, Aurora Ontario, Canada, water cooler replacement parts

click on image to go to TEC peltier Module Specification's

Cooling Chips

We carry numerous Peltier chips ( Thermoelectric Chips ) all at very competitive prices. We have been dealing with chips for 15 years . If you prefer sealed or unsealed, we can supply them.

Cascade or singles peltier chips. Just let us know! Water Cooler replacement Tec's . Thermoelectric peltier modules are the most important part of the water cooler.

Evaporators coils

High efficiency heat pipe coils with water as the working fluid in a vacuum. ( NO CFC'S)

This heatpipe is not only environmentally friendly, but requires NO compressor. It uses evaporative cooling and convection to cool, is extremely efficient and requires very little forced convection (fan speed) to cool. You can cool a custom cabinet for wine, which holds 100 bottles, using two evaporators and produce little or no noise.

W x L x H

3" x 17" x 12" evaporator part # EV 001

( single 6 amp)

W x L x H

3" x 17" x 12" evaporator part # EV 002

( Two - 6 amp)